How To Set Mole Traps

Fix Takes Simply a Few Simple Steps

The Tomcat® Mole Trap offers speed and prophylactic in controlling moles. This particularly designed "hands-free" mole trap is fast and easy to place and set. Learn how to use the Tomcat® Mole Trap along with additional tips.

How to Utilise a Tomcat® Mole Trap

Footstep 1: Locate Active Tunnels

The Tomcat® Mole Trap needs to be set in a main runway. These are the main tunnels about often traveled by the mole. They are usually straight or will follow the perimeter of your yard. To determine if a tunnel is a primary runway:

• Use a 1/2" dowel or your finger to puncture holes in the tunnels. Be careful not to beat the tunnels.


• Mark the holes with lawn flags or sticks.


• Revisit later on 24-48 hours. If the hole has been repaired, it indicates information technology'southward a main runway existence used past the mole.

Footstep 2: Fix the Tunnel

In one case you take found an active tunnel, y'all will need to prepare the tunnel before y'all tin can ready the trap. First, use your heel to create a 1-inch indentation for trigger in heart of the active tunnel. (The built-in Depth Estimate should fit in the indentation to confirm that information technology's the correct depth.) Then employ the trap jaws to mark the tunnel on each side of the indentation you just fabricated for the trigger and use a backyard edger or foursquare-bladed spade to cut and widen 5-inch deep slots across the tunnel so the trap tin exist easily inserted.

Step 3: Insert Trap

Once you accept the expanse of the tunnel prepared, it'southward time to set the Mole Trap. Insert the trap jaws into the slots you cutting across the tunnel.

Step 4: Set Trap

And so step direct down on the high end of the yellowish foot pedal. (Exist careful not to cover the trigger slot on the pedal with your foot.) Continue to push the foot pedal down until the trap latches and the trigger postal service comes through the trigger slot.

Step 5: Activate Trigger

Finally, utilise your foot to printing the trigger post flush with the superlative of the human foot pedal. (The base of the trap should be flat on the footing when it is gear up correctly.) Your Tomcat® Mole Trap is now set up.

Footstep vi: Removing a Trapped Mole

When the foot pedal is in the raised position it indicates that you've trapped a mole.

Then to release the mole, set the trap on a bucket and shrink the foot pedal with your hand.

Tips & Troubleshooting

one. If the trap won't set:

• Do non leap on it! If slots were cut in the tunnel, the trap should set hands. If you go on to meet resistance, movement the trap to another tunnel location.


• Cheque that the trigger indentation has not filled in with soil while you lot tried to set the trap. Make the trigger indentation again and then continue to reset the trap.


• Brand sure mud isn't interfering with the trap's catch motion. Clean off the trap and then try setting information technology in another location.

2. Poke a pigsty in the tunnel 6-inches away from each side of the trap. After 1 week, if 1 or both of the holes have been sealed and the trap didn't spring bank check the trigger mail service. If it is upwards ane-inch above the pes pedal, employ a spade to pry the trap upwards from the ground which should spring the trap. Make clean off any dirt and mud then motility the trap to another tunnel location and reset.

iii. If you lot push the safety release button on the trap and it doesn't spring, follow the same steps as above.

4. If the soil is very soft, the trap could be pushed too far into the basis. It is better to set the trap in a location with firmer soil.

Moving & Reusing

If at that place has been no activity after a week move the trap to a new location. To release the trap, place your foot lightly on the pedal and a utilize dowel to press the safety release push. (The trap will spring upwards when the latch is released.)

Before storing, the trap should be cleaned so dried mud does non interfere with future trap use.

Source: https://www.tomcatbrand.com/en-us/library/using-mole-and-gopher-traps/how-use-tomcat-mole-trap

Share this post